Mammut symbolises the breakthrough of modular panel systems, pioneered by MEVA, into civil and industrial engineering. In 1982, the original Mammut was the first system ever to make large-scale pours possible, saving time and money. In 2003, its successor system Mammut 350 set the industry's benchmark with its 100 kN/m² concrete load capacity throughout the system (not merely with some panels). With its all-plastic facing and its symmetrical tie-hole and joint imprint, Mammut 350 has become the leading formwork system for architectural finish in civil engineering, commercial and residential construction. For sale and rental.
Panel size 350 x 250 cm with a surface of 8,75m² for floor heights of 350 or 250 cm with one panel used in vertical or horizontal Position
Heights 350, 300, 250 and 125 cm, panel widths from 250 to 25 cm; for vertical or horizontal use
90° and 135° inside and outside corners and steplessly adjustable articulated corners from 60° to 180°. Articulated corner with interlocking device for frequent angles.
Maximum load capacity is 100 kN/m² (German standard DIN 18218, table 3, line 7)
Frames made of closed, high-strength hollow steel profiles
High-quality annealed powder coating with additional priming and cavity sealing
250 cm and 125 cm wide panels with bump notch
Practical MEVA multi-function profile with welded-in Dywidag nuts; additional multi-function profiles at tie hole level
Tie hole with conical steel anchor sleeve, welded in from both sides
3 tie holes per panel height 350 cm, 2 per panel height 300 and 250 cm, 1 per panel height 125 cm; symmetrical arrangement
Panel connection with compact MEVA assembly lock: no losable parts, weighs only 3,0 kg
All-plastic facing alkus, no swelling or shrinking
Easy repair of scratches or drill holes etc. on site with the same polypropylene material
Screwable and nailable without chipping off of top layer
The alkus facing lasts as long as the Frame
can be done with alignment rails and tie rods using a total of 10 parts, or with just one part: the stop-end bracket 40/60: Place, tie it, done!
All corner above 60° are achieved with inside, outside and hinged corners.
All attachments of parts are achieved using the same flange screw addressing the welded-in DW thread on the multi-function profile. Walkway brackets are equipped with a pin which attaches to the same thread and automatically locks in safe position. Safety accessories such as walkway brackets and working platforms stay in position, safely and firmly attached.
MEVA STB 450 offers flexible solution for narrow, inclined rail section: Near the municipality of Gretzenbach, the four-track route branches into two separate lines. Here, the two southern tracks gradually descend and pass below the cantonal road before entering the new Eppenberg Tunnel.
Four apartment buildings at heights up to 202 m by 2020: the city centre redevelopment project Deansgate Square. In use for a total of 194 storeys: the automatic MAC climbing system from MEVA
In Zurich the motorways cross each other from all directions. Every morning and evening in this densely populated region the heavy through and long-distance traffic is joined by commuter traffic.
The STB 450 has often proved its strength when being used vertically to support walls. For a motorway bridge north of Frankfurt it is being used horizontally for the bridge piers.
Putting superlatives on Dubai’s skyline continues with the construction of the Rosemont Hotel and Residences on Sheikh Zayed Road.
Located between Sharjah and Dubai, close to Dubai International Airport, yet close to all amenities – Sahara Tower 6 is a residential tower offering luxury apartments with various bedroom configurations.
MEVA pouring platforms, walkway brackets and comprehensive safety accessories make your concrete pours safer and faster. The pouring platform is simply swung into position on the AluStar, StarTec, Mammut or Mammut 350 wall formwork panels.
Circo is a robust steel system with integrated hinge joints for circular columns. It is available in 5 cm steps from 25 to 80 cm and in heights of 50, 100 and 300 cm. The two shells are closed using the standard M clamp.
Modular system for heavy duty bracing. The brace lengths are variable and can be used to support and align high walls and columns beyond 6 m heights.
MEVA foldable working and climbing platform. It is delivered to the site folded and pre-assembled and can be used as a climbing platform.
Three tieing methods in one system. The sytem‘s integrated Combi tie of using any of the following tieing methods and flexibly changing from one to another:
MEVA FormSet anchors for single-sided formwork, stop end rail and stop end bracket for slab edges and cantilevering slabs with safety mesh for slab edge fall protection
Push-pull props R and bracing brackets SRL are used to align and support wall formwork. Push-pull props SRL have left- and right threaded spindles. The brace bracket 250 consist of a push-pull-prop R 250 (190 - 320 cm) and bracing bracket SRL 120 (90 - 150 cm).
Radius is the state-of-the-art circular wall formwork systems for all round walls from a radius of 250 cm upwards. It is compatible with the Mammut 350 wall formwork system and is joined using the same M formwork clamp. It has a sturdy 6 mm steel facing for a superior concrete finish. Its benefits are very quick, easy assembly and the easy selection of any radius. Box outs are aligned using high-performance magnets. Predestined for architectural requirements.
Comprehensive, modular safety system for MEVA wall wall formwork systems. Easy, standard attachment to the multi-function profile. Baukastensystem mit Betonierbühne, Rückenschutz, Frontgeländer und Durchstiegsluke mit Leiter und Stirngeländer. Befestigung an der Funktionsstrebe des Wandschalungssystems. Richtkonsolen am Rücken der Laufkonsole, dadurch keine Unterbrechung der Arbeitsbühne.
Heavy-duty support frame for single-sided walls beyond 12 m high. The basic unit fits on any truck. Support frame STB 300, can also be used horizontally.